在操作數控焊接設備時容易出現的一些問題，如果你在使用中遇到了這些問題，可以參考以下的方式進行解決，接下來我們來看看在使用設備時要注意哪些?

If you encounter some common problems when operating CNC welding equipment, you can refer to the following methods to solve them. Next, let's take a look at what to pay attention to when using the equipment?

1.操作機器的人員一定要熟悉設備的結構以及工作原理和操作方法。

1. Personnel operating the machine must be familiar with the structure, working principles, and operating methods of the equipment.

2.機器操作人員不能戴手套進行操作，女工長發應盤起，不許穿太過寬松的衣服，不準接觸皮帶，傳動部分，刀片等，防止傷人。

2. Machine operators are not allowed to wear gloves for operation. Female workers should curl up their long hair, wear too loose clothes, and do not touch belts, transmission parts, blades, etc. to prevent injury.

3.山東數控焊接設備機器開機前，應檢查送紙臺面有無放置工具或其它雜物，每次開機時一定要先按電鈴，有了本機別的操作員工響應后，方可開機。如果按完電鈴后不開車，過一段時間再開車要再按電鈴，確認沒有問題后再進行運轉。啟動機器不準直接高速運轉，需從速度零開始，逐漸通過速度旋鈕達到額定工作速度。

Before starting the Shandong CNC welding equipment machine, it is necessary to check if there are any tools or other debris placed on the paper feeding table. Each time the machine is started, it is necessary to press the electric bell first. Only after other operators of the machine respond can the machine be started. If you do not drive after pressing the bell, and then drive again after a period of time, you need to press the bell again to confirm that there are no problems before running. Starting the machine at high speed is not allowed. It needs to start from zero speed and gradually reach the rated working speed through the speed knob.

4.開槽部分要按程序操作，開槽刀和分紙刀的刀口都很鋒利，ji易傷手;開槽上刀一定要落在下刀槽里，處于正中位置調好刀后一定要鎖好緊固螺絲，并要注意把鏟紙刀放入鏟紙槽里。

4. The slotting part should be operated according to the program, and the cutting edges of the slotting knife and the paper separating knife are very sharp, which can easily hurt hands; The upper knife of the slot must fall into the lower knife slot, be in the center position, and after adjusting the knife, be sure to lock the fastening screws, and pay attention to placing the paper scraper into the paper scraper slot.

四刀聯動調好后也要記得鎖緊螺絲，各部調好鎖緊后先用手柄轉動開槽部幾圈，如無異?，F象方可繼續操作設備。在高速運轉時，稍不留神手就會碰到鋒利的刀口上，特別要當心。在生產時，如果違反操作規程也很容易造成傷害事故，所以也要注意。

After the four blade linkage is adjusted, remember to tighten the screws. After each part is adjusted and locked, first use the handle to rotate the slotted part a few turns. If there are no abnormalities, continue operating the equipment. When running at high speed, if you don't leave your hand behind, you will hit the sharp edge of the knife, so be particularly careful. During production, it is also easy to cause injury accidents if operating procedures are violated, so attention should also be paid.

技術人員在使用數控焊接設備時，一定要注意以上幾點內容，不要因為一時的粗心引發事故，如果出現了一些常見問題，可以根據實際情況進行維修，自己維修不了，可以找相關的維修人員處理。更多相關事項就來我們網站http://www.hk809.com咨詢吧！

Technicians must pay attention to the above points when using CNC welding equipment, and do not cause accidents due to carelessness. If some common problems occur, they can repair them according to the actual situation. If they cannot repair them themselves, they can find relevant maintenance personnel to handle them. For more related matters, come to our website http://www.hk809.com Consult!